Gelenklager Gelenkköpfe Spherical Plain Bearings Rod Ends - Gelenkkoepfe

DE
EN

GARS05Druck

FLURO-No. GARS 05

statische Tragzahl C_o kN static load C_o kN	dynamische Tragzahl dynamic load C kN	zulässige Drehzahl limiting speed rev/min	Stückgewicht gr. / lb. part weight gr. / lb.
6,2	3,3		13 / 0,0287
nicht nachschmierbar / without lubrication fitting

GARS03Druck

FLURO-No. GARS 03

statische Tragzahl C_o kN static load C_o kN	dynamische Tragzahl dynamic load C kN	zulässige Drehzahl limiting speed rev/min	Stückgewicht gr. / lb. part weight gr. / lb.
7	1,8		6 / 0,013
nicht nachschmierbar / without lubrication fitting

GIRS40RDruck

FLURO-No. GIRS 40 R

statische Tragzahl C_o kN static load C_o kN	dynamische Tragzahl dynamic load C kN	zulässige Drehzahl limiting speed rev/min	Stückgewicht gr. / lb. part weight gr. / lb.
235	116	290	2770 / 6,107

Rod Ends Series K - Stainless housing - Requiring maintenance

Series GARS

Rod Ends with male thread regreasable through the housing with flush type grease fitting

For use in corrosive environments

GARS-Drawing

Size (D H7)	B	M	A	F	L	O	G	GL	Static load C_o kN	Dynamic load C kN	Limiting speed rev/min		Pivoting angle α (°)	Weight g
3¹⁾	6	4,5	14	26	33	5,1	M 3	15	7	1,8			14	6
5¹⁾	8	6	18	33	42	7,7	M 5	19	6,2	3,3			13	13
6	9	6,75	20	36	46	8,9	M 6	21	8,8	4,3	1500		13	20
8	12	9	24	42	54	10,4	M 8	25	16,1	7,1	1200		14	33
10	14	10,5	28	48	62	12,9	M 10	28	25,5	10	1000		13	56
12	16	12	32	54	70	15,4	M 12	32	34,5	13,5	860		13	87
14	19	13,5	36	60	78	16,8	M 14	38	39,5	17	750		16	129
16	21	15	42	66	87	19,3	M 16	40	60,5	21,5	660		15	189
18	23	16,5	46	72	95	21,8	M 18x1,5	44	73	26	600		15	267
20	25	18	50	78	103	24,3	M 20x1,5	47	83	31,5	540		14	348
22	28	20	54	84	111	25,8	M 22x1,5	51	100	38	500		15	443
25	31	22	60	94	124	29,6	M 24x2	57	118	47	440		15	600
30	37	25	70	110	145	34,8	M 30x2	71	155	64	370		17	1030
35	43	28	80	125	165	37,7	M 36x2	73	191	80	330		19	1600
40	49	35	90	142	187	44,2	M 42x2	78	235	116	290		16	2570

Materials:
Housing:	Stainless steel to 1.4057, Aisi 431, forged, polished
	Size 40 made from stainless steel to 1.4057, Aisi 431, turned
Insert:	Special high strength bronze to CuSn8
Ball:	Bearing steel to 100Cr6, Aisi 52100, hardened, ground, polished, hard chrome plated on the running surface
On request:	Other tribological pairing possible

This series is also available on request in some sizes sealed (-2RS) or with threaded bolt (-BO).

¹⁾ Without lubrcation fitting

Page 127 of 159

FLURO^®-Gelenklager GmbH
Siemensstrasse 13
72348 Rosenfeld, Germany
0049 7428 / 9385-0
info[at]fluro.de

Contacts:
National / International

Legal notes:

Data protection

Newsletter:

Subscribe to our newsletter

>> Subscribe here

X

Right Click

No right click